Pressure-sensitive (PSA) self-adhesive coating of roll materials

FERCOS coats roll materials with a hot-applied pressure-sensitive adhesive (PSA), on one or both sides, and protects it with release paper or film. Your customer peels off the protection and bonds by pressure, without applying any glue. We work to order.

Request a quote

How self-adhesive coating works

PSA is an adhesive that stays tacky for good. It bonds when you press on it, and the more pressure, the better the adhesion. We apply the hot melt adhesive to your roll material and cover the layer with release paper or a technical film, which comes off only at the moment of bonding.

The coating can go on one side or on both. Each coated side keeps its own protection.

Because the tack is permanent, the adhesive also works for pre-bonding. The material is ready to be bonded later and elsewhere, whatever the place and moment the adhesive was applied.

If what you need is to join two materials with the PSA between them, see direct bonding.

Direct bonding of two materials

Three measures decide the right PSA

The adhesive we apply is a 100% solid PSA hot melt, with no solvents or water. Which one to choose depends on three measures, and they pull against one another.

Peel adhesion

The force needed to separate the adhesive from the surface it bonded to. High values suit permanent joints, such as double-sided tape that replaces a mechanical fastener. Low values suit temporary fixing.

Tack

The initial stickiness, on light contact. Low tack leaves less residue and suits delicate surfaces. High tack grips fast, but does not let you reposition the part.

Shear

The ability to hold when pulled in the same plane as the adhesive. The higher it is, the less the part gives, but the worse the adhesive wets the surface, and tack and adhesion tend to fall.

  • Before choosing, we ask you five questions. What will the adhesive be used for, and where?
  • How long must it last: an assembly aid, a permanent fixing, or removable and repositionable?
  • What materials will it bond to? Surface energy, texture and dirt all count.
  • What environment will it work in? Heat, cold, humidity, solvents, dust and oils all count.
  • What stresses will it meet over the life of the product?

Materials we coat with adhesive

We work with roll materials. Low surface energy surfaces repel the adhesive and may not bond, so we advise a trial with your material first.

  • Technical textiles, woven fabrics, knits and nonwovens
  • Foams, rubbers, latex and silicone
  • Lace and felts
  • Synthetics and synthetic leather
  • Paper and cellulose
  • Cork and insulation

Where a self-adhesive material is used

Footwear

Components bonded by pressure at assembly, with no oven or heated press.

Automotive

Parts and double-sided tapes that replace mechanical fasteners, with less weight and simpler assembly.

Technical and home textiles

Fabrics and foams the customer fixes to another substrate at assembly.

Furniture and packaging

Materials with the adhesive protected by release paper, ready to apply.

Footwear and insolesAutomotiveHome textiles and mattresses

Technical capabilities

ParameterValue
Coated sidesOne side or both sides
Adhesive protectionRelease paper or technical film, on each coated side
Usable coating widthOn request
Adhesive weight (g/m²)On request
SubstratesIn roll form: technical textiles, fabrics, knits, nonwovens, foams, paper, cork and synthetics
Minimum order and sample quantityOn request
Typical lead times (sample and production)On request
Delivery formatOn request

Advantages and limitations

Advantages

  • It bonds by pressure. Whoever assembles has nothing to reactivate.
  • Permanent tack allows pre-bonding and assembly in two steps.
  • It is 100% solid, with no solvents or water, and the glue line is elastic.
  • It levels small irregularities in the surface.
  • It replaces screws and rivets, with less weight and simpler assembly.

Limitations

  • It depends on the surface: it must be clean, free of dust, oils, grease and release agents.
  • It needs the right pressure, time and temperature. If the part goes into service before the adhesive has wetted the surface, the bond does not reach its maximum and may fail.
  • Plastics and other low-energy surfaces can repel the adhesive.
  • Rubber-based PSAs resist solvents and plasticisers poorly, and have limited heat resistance.
  • There is no single answer: more tack means less repositioning, and more shear means less tack.

Guide: Hot melt, PUR or PSA?Hot melt coating

The adhesive is measured too

The FERCOS traceability system covers every adhesive family, PSA included. It records adhesive weight, width, tensions, temperatures, pressures and the adhesive lot, per customer and per production run. Adhesive peel is tested as well.

Quality and certifications

From the roll to the adhesive

Self-adhesive textile being separated from its silicone release paper
Diagram of the peel test of an adhesive film on a substrate

Frequently asked questions

Is the adhesive on one side or both?

It can be on one side or on both. Each coated side has its own protection, in release paper or technical film.

Can I receive the material already coated, to bond later?

Yes. Because the tack is permanent, the material arrives pre-coated and bonds when you press on it, wherever and whenever the adhesive was applied.

Does PSA bond to any material?

No. Low surface energy surfaces repel the adhesive, and dirt, oils and release agents prevent adhesion. That is why we advise a trial with your material first.

What is the difference between PSA and heat-activated hot melt?

PSA bonds by pressure and stays tacky. Heat-activated hot melt is dry to the touch and only bonds when your customer reactivates it, with heat and pressure.

What is the minimum order and the lead time for a sample?

Tell us what you need and we will reply with a quote.

Request a quote for your self-adhesive material

Tell us the material, the roll width, one or two sides, the surface it will bond to, and the quantity. You can attach data sheets and specifications.

Request a quote