Technical guide
Hot melt, PUR or PSA? How to choose the adhesive for your material
The three adhesives FERCOS applies to roll materials bond in different ways and withstand different things. This guide compares them side by side and says when to use each one, and where each one fails.
Request a quoteThe three adhesives in one sentence
All three are 100% solid, with no solvents or water, and of EU origin.
Heat-activated hot melt
A thermoplastic, dry to the touch, that bonds when you reactivate it with heat and pressure and softens again if heated once more.
Hot melt coatingReactive PUR
A polyurethane that bonds hot and then cures with moisture, over 24 to 72 hours, until it is an elastomer that no longer softens.
Reactive PUR laminationPSA self-adhesive
An adhesive that stays tacky for good and bonds by pressure, at room temperature, protected by release paper or film.
PSA self-adhesive coatingSide-by-side comparison
The values are typical of each family, according to the adhesive suppliers. They do not guarantee a specific product.
| Hot melt | Reactive PUR | PSA | |
|---|---|---|---|
| How it bonds | Reactivated with heat and pressure | Cures with moisture | Bonds by pressure |
| State of the coated material | Dry to the touch, waiting for reactivation | Sets as it cools and cures afterwards | Tacky, protected by release paper or film |
| Application temperature | EVA: 180 to 190 ºC | 85 to 140 ºC | On request |
| Time to final strength | Immediate, on cooling | 24 to 72 hours | Depends on application pressure, time and temperature |
| Heat once bonded | Softens again. Polyolefin and copolyamide resist better than EVA | High, after curing: it cross-links and does not soften | Limited in rubber-based PSAs |
| Elasticity | Depends on the formulation | High, before, during and after cross-linking | Elastic glue line |
| Repositioning the part | No: it bonds on reactivation | No, after curing | Possible with low tack |
| Reactivatable by heat | Yes | No, after curing | On request |
| Difficult materials | EVA: the widest range; polyolefin: good on foams and textiles | Strong on difficult substrates, but not on PE, PP, PTFE or silicones | Low-energy surfaces repel the adhesive |
Which to choose, depending on what you need
- You need to deliver the material ready to be bonded later, hot: hot melt.
- You need an elastic bond that resists heat, water and washing: reactive PUR.
- You need to bond without heat, by pressure, or to pre-bond: PSA.
- You need to join two materials: direct bonding, with the adhesive the end use calls for.
- You need three or more layers: multilayer lamination, with the right adhesive at each joint.
Where each one fails
Hot melt
Being thermoplastic, the bonded assembly must not pass the softening point of the adhesive. EVA and polyolefin resist solvents and plasticisers poorly.
Reactive PUR
It needs curing time and moisture. It does not adhere, or adheres poorly, to polyethylene, polypropylene, PTFE and silicones, and is not for materials that stay immersed.
PSA
It depends on the surface, which must be clean and not low-energy, and on pressure, time and temperature. More tack means less repositioning.
Five questions before deciding
- What will the product be used for, and where?
- What heat, water, washing or stress does it have to withstand?
- What materials will it bond to? Are there low-energy plastics or dirty surfaces?
- How will your customer assemble it? With a hot press, or by hand, by pressure?
- How much time is there for curing, before the material is used?
Frequently asked questions
Which is the best adhesive?
None is best at everything. Hot melt is fast and reactivatable, PUR is elastic and resists heat and water once cured, PSA bonds by pressure without heat. The choice comes from the end use.
Is PUR always more heat-resistant than hot melt?
Once cured, yes, because it cross-links and stops softening. Polyolefin and copolyamide also resist heat well, and EVA less so.
Can I mix adhesives in one part?
Yes, in multilayer laminates. The adhesive is chosen joint by joint, from the materials each one joins.
Do all three contain solvents?
No. All the adhesives FERCOS applies are 100% solid, with no solvents or water base.
How do I know which to choose for my case?
Tell us the materials, the end use and what the product has to withstand. We propose the adhesive and, if needed, a trial with your materials.
Not sure which to choose? Tell us the end use
Tell us the materials, the end use and what the product has to withstand. We propose the adhesive and the process.
Request a quote