Service · Hot melt
Hot melt coating of roll materials
FERCOS applies 100% solid hot melt adhesives to textiles, foams, nonwovens, paper and membranes in roll form. The material leaves coated and ready to be bonded later, with heat and pressure, on your customer's line. We work to order, and have done so since 1976.
Request a quoteHow hot melt coating works
The adhesive arrives solid, is heated until it melts and is laid onto your roll material. As it cools it sets on the surface and waits. Later, when your customer applies heat and pressure, the adhesive melts again and bonds the material to another. That is why the coating is called heat-activated, or thermo-adhesive.
The layer can be continuous (a full coating, which does not breathe) or leave the material breathable. What decides it is the type and amount of adhesive applied, and we choose both for the end use.
For delicate materials, such as nonwovens, light fabrics, knits and foams, we use transfer coating. The adhesive is coated first onto a special paper, passes from it to the material under pressure and cooling, and the paper is peeled away. Only the adhesive film stays on the material, ready to be reactivated later.
Hot melt adhesives we apply
Each family has its own chemistry and its own limits. We choose the formulation from the materials to be bonded, the process and the environment the final product will work in. The figures below are those of each family, as given by the adhesive suppliers, and are not a guarantee for a specific product.
EVA (ethylene-vinyl acetate)
Bonds the widest range of materials and is the most affordable. It is usually applied between 180 and 190 ºC and works in service from -5 to 70 ºC, depending on the formulation. Common in technical textiles, footwear and insoles.
PO (polyolefin, metallocene)
Better heat and moisture resistance than EVA, low viscosity and a long open time, with good adhesion to foams and textiles. It stands -40 to 80 ºC in service, with a melting point near 150 ºC.
CoPA (copolyamide)
For when the bonded assembly will meet heat during manufacture, transport or use. It resists heat, solvents and plasticisers better than polyolefin.
CoPES (copolyester)
High peel strength and good adhesion to textiles, plastics and some metals. It withstands high temperature and the migration of plasticisers and water.
- All are 100% solid, with no solvents or water, and of EU origin. We also have biodegradable and flame-retardant formulations.
Materials we coat
We work with roll materials. You can send your own, or ask for one of those we supply (nonwovens, knits, foams, twills).
- Technical textiles, woven fabrics and knits
- Nonwovens and felts
- EVA, neoprene, PU and latex foams
- Membranes and films
- Paper, cellulose and decorative foils
- Glass fibre, cork, lace and synthetic leather
Where a hot melt coated material is used
These are the most frequent sectors. We also serve furniture and packaging.
Footwear and insoles
Parts that the footwear maker later bonds, hot, to the upper, to foams or to the insole.
Automotive
Coated textiles and foams for interiors, which the customer applies with heat and pressure.
Home textiles and mattresses
Laminates and interlinings for home fabrics, protectors and mattresses.
Technical and functional clothing
Materials fixed by heat, with no stitching, in sports, protective and functional clothing.
Technical capabilities
| Parameter | Value |
|---|---|
| Usable coating width | On request |
| Adhesive weight (g/m²) | On request |
| Substrates | In roll form: technical textiles, fabrics, knits, nonwovens, foams, paper, membranes and films |
| Substrate thickness and weight | On request |
| Minimum order and sample quantity | On request |
| Typical lead times (sample and production) | On request |
| Delivery format | On request |
| Process control | Automatic monitoring of adhesive weight, width and tensions |
Advantages and limitations
Advantages
- It is 100% solid: no solvents, no water, and no relevant VOC emissions.
- It reactivates with heat: your customer bonds when they choose, without applying glue again.
- It cools and sets: adhesion rises quickly after cooling, which gives production speed.
- It can leave the material breathable or seal it, depending on the adhesive and the amount.
- The surface stays smooth and clean, because bonding uses no water or solvents.
Limitations
- It is a thermoplastic and softens again with heat. The bonded assembly must not pass the adhesive's softening point; if it will, look at reactive PUR.
- EVA and polyolefin resist solvents and plasticisers poorly. Copolyamide does better.
- It does not bond at room temperature. Adhesion forms when your customer reactivates the adhesive, with controlled heat and pressure.
- It is not self-adhesive. To bond by pressure, without heat, look at PSA coating.
Guide: Hot melt, PUR or PSA?Reactive PUR laminationPSA self-adhesive coating
Weight and width measured continuously
The FERCOS system automatically monitors adhesive weight, coating width and material tensions, and records temperatures, pressures and adhesive lot, per customer and per production run. If you need to know what happened to a roll, it is on record.
The coating line


Frequently asked questions
Do you coat my material, or do you have to supply it?
Either works. You can send us your roll material, or ask for one of those we supply: nonwovens, knits, twills, foams.
Does hot melt coating breathe?
It depends on the type and amount of adhesive. It can stay breathable or form a continuous layer, which does not breathe. Tell us the end use and we suggest the right one.
What is the difference between hot melt and PSA?
Hot melt bonds when your customer reactivates it with heat and pressure. PSA is self-adhesive: it bonds by pressure, at room temperature, and is protected by release paper or film.
What is the maximum width you can coat?
Tell us the width of your roll and we will confirm.
Do the adhesives contain solvents?
No. We only use 100% solid adhesives, with no solvents or water base, of EU origin.
Request a quote for your material
Tell us the material, the roll width, the adhesive or end use, and the quantity. You can attach data sheets and specifications.
Request a quote